Whirlpool Error Codes
Explanations follow official Whirlpool support pages.
Whirlpool dishwasher codes
- F6E3Excessive suds detected in the tub, which can stop the dishwasher from filling or operating properly.
- F6E4Water float (overfill) switch error - incorrect leveling can actuate the overfill/float switch and trigger this code.
- F8E2Fill valve electrical error. Whirlpool suggests removing the drip tray to inspect the inlet valve connection for leaks, then power cycling.
- F8E4Water detected in the drip tray - a possible leak or overflow, common after a new installation.
- F8E5Fill valve stuck open - water may keep entering the dishwasher. Whirlpool says to shut off the water supply.
- F9E1Long drain condition - the dishwasher is not draining. Whirlpool lists checks for the filter, drain hose, sink disposer, and air gap, then a power cycle.
- F9E2Drain motor error. Whirlpool lists drain-path checks (disposer knockout, clogs, kinked hose, hose routing), then a power cycle; service if it returns.
- FAE5Diverter leak. Whirlpool says to check for leaks under the dishwasher and confirm water connections are secure, press Cancel twice, and try a new cycle.
- H2OThe dishwasher is not detecting incoming water. Whirlpool says to verify the water supply is on and the supply hose is not kinked.
Whirlpool washer codes
- DLOLid lock will not lock / lid lock failure. Whirlpool Washer code DLO: what the manufacturer says to check and when to call service.
- DUThe lid cannot unlock because objects on the washer lid are preventing it. · also LDU
- ERRMessage shown when you try to change or modify a cycle while the washer is running, or try to start a cycle with the door open.
- F0E2Excessive suds were detected in the basket; the washer runs an automatic suds-reduction routine, so let it continue.
- F0E4The washer senses the water temperature is too hot, typically because the hot and cold inlet hoses are reversed.
- F20Water inlet problem: no water or insufficient water supply detected. Whirlpool Washer code F20: what the manufacturer says to check and when to call
- F21Drain problem: the washer is not draining. Whirlpool Washer code F21: what the manufacturer says to check and when to call service.
- F22Front door lock issue: the washer cannot lock the door. Whirlpool Washer code F22: what the manufacturer says to check and when to call service.
- F5E1Door switch fault: the door must be completely closed with nothing blocking the door switch.
- F5E2The washer cannot engage the lid lock, possibly because of an obstruction in the lid lock area.
- F5E3Door lock fault; the official page directs a control power-cycle reset.
- F5E4The washer has run three consecutive cycles without the door being opened.
- F8E1The washer is not detecting the correct amount of incoming water (low fill); the display may also show Lo FL, LF or No Water Detected. · also LOFL, LF, NOWATERDETECTED
- F8E3Overflow condition: too much water or foam in the washer. Whirlpool Washer code F8E3: what the manufacturer says to check and when to call service.
- F8E6Two possible meanings depending on the model: the lid is open during the soak cycle, or no hot water was detected.
- F9E1The washer is unable to drain correctly (long drain time). Whirlpool Washer code F9E1: what the manufacturer says to check and when to call service. · also DRN
- FHWater inlet problem: no or insufficient water supply detected. Whirlpool Washer code FH: what the manufacturer says to check and when to call service.
- HCHot and cold inlet hoses installed reversed; the code appears at the end of the wash cycle.
- INTThe cycle was paused or cancelled; the washer can take 20-30 minutes to stop spinning and drain, and shows this code during that time.
- LDLong drain: drain pump system problem - the washer is taking too long to drain water.
- LDLLid lock will not lock (lid lock failure). Whirlpool Washer code LDL: what the manufacturer says to check and when to call service.
- LIDThe washer lid was left open. Whirlpool Washer code LID: what the manufacturer says to check and when to call service.
- SDExcessive suds in the washer; the washer runs a suds-reduction routine.
- SUDToo many suds in the washer; the washer extends the rinse time to remove them.